How Do You Manually Reset a Car Code?

When your vehicle’s check engine light appears, it often indicates various potential issues.

While modern automotive diagnostic scanner allow us to identify these error codes accurately, there are cases where you may want to clear these codes manually.

Below, we’ll guide you through the exact steps to manually reset car codes and explain when it’s appropriate to do so.

What Are Car Codes, and Why Do They Appear

Your vehicle's onboard diagnostics system (OBD) continuously monitors engine performance, transmission, fuel system, and other vital components. When an issue is detected, the system generates a code known as a diagnostic trouble code (DTC). These codes provide insight into the potential issues affecting your vehicle.

Clearing these codes, however, should not be a substitute for addressing underlying issues. Resetting codes without repairs may cause the check engine light to return if the fault persists.

Related Reading: How to Clear Codes on Cars with Scanners

Methods to Reset a Car Code

Method 1: Disconnect the Battery 

Disconnecting the battery is one of the simplest ways to clear a car code, as it resets stored error codes and turns off the check engine light.

1. Turn Off the Car: Make sure the ignition is completely off.

2. Disconnect the Battery Cables: Use a wrench to first remove the negative (black) cable, then the positive (red) cable.

3. Drain Any Remaining Power: Press and hold the brake pedal for around 30 seconds to fully drain residual power.

4. Wait 10-15 Minutes: Allow time for the system to reset.

5. Reconnect the Battery Cables: Attach the positive cable first, then the negative.

6. Start the Car: Check if the check engine light has turned off.

Note: Disconnecting the battery may also reset settings like radio presets and the clock.

Method 2: Use the Ignition Key Trick

This is a quick and easy method that doesn’t require opening the hood.

1. Turn the Key to “On”: Insert your key and turn it to the “On” position without starting the engine.

2. Cycle the Key: Turn the key off, then back to “On” three to five times, pausing briefly each time.

3. Check the Light: Start the car to see if the check engine light has turned off.

Note: This trick works for some car models, though results may vary.

Method 3: Pull the ECU Fuse

For vehicles with an accessible ECU (Engine Control Unit) fuse, removing it briefly can reset codes without affecting other settings.

1. Find the Fuse Box: Locate the fuse box, typically under the hood or dashboard.

2. Identify the ECU Fuse: Check your owner’s manual to locate the specific fuse for the ECU.

3. Remove the Fuse: Use pliers or a fuse puller to carefully remove the ECU fuse.

4. Wait 5-10 Minutes: Allow the system time to reset.

5. Reinsert the Fuse: Place the fuse back securely in its slot.

6. Start the Car: Check if the check engine light has reset.

Method 4: Complete a Drive Cycle

Completing a “drive cycle” can sometimes automatically clear minor error codes.

1. Warm Up the Engine: Let your car idle until it’s fully warmed up.

2. Drive with Mixed Speeds: Drive for about 15-20 minutes, mixing highway and city speeds.

3. Check for Code Clearance: This lets your car’s system re-evaluate the issue, which may clear the code automatically.

ANCEL V6 PRO+ Bluetooth Bidirectional Scan Tool Full System Car Diagnostic Tool Key Programmer
$439.99

shop now

Why Not Use an OBD2 Scanner?

While manual reset techniques can be effective, an OBD2 scanner ANCEL V6 pro is typically the most reliable tool for managing car codes. A quality car diagnostic scanner automotive offers advantages, such as:

• Quick Diagnostics: Instantly identify and read trouble codes by using bluetooth obd2 reader.

• Permanent Code Clearing: Clearing codes with advanced car diagnostic tool after repairs without the risk of battery resets or fuse removal.

Conclusion

Manually resetting car codes can be done effectively with methods like battery disconnection, key cycling, ECU fuse removal, and drive cycles. However, we advise using these techniques only after identifying and fixing the root cause of the error.

Recommended Similar Articles：

• Where Can I Get My Check Engine Codes Read
• Why You Should Consider Getting the Ancel Ad410
• Do You Need a Heavy Duty Truck Scanner
• What is a Good Bi-directional Scan Tool
• How to Read a Car Key Code